1220冷连轧机带钢表面振纹机理的研究

doi:10.3969/j.issn.1000-1158.2015.06.09

Abstract
Figure/Table
References (16)
Related Citation (15)

Download: PDF (1757 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Aiming at a 1220 strip surface, where the cold rolling mill had chatter marks, on which the reasons for the formation was tracked tested for in-depth study.Based on the vibration test, the analysis was given to the dynamic characteristics of the rack and the various phases of work rolls in the cycle on vibration signal.It was found that in its middle or late phase of the backup roll being used, the mill mainly worked with the 7th-order natural vibration at app.600Hz. When the rolling speed was maintained in the stable middle-/high-speed rolling phase, the relative movement of the work roll to the intermediate roll caused the formation of the chatter marks in the work roll surface.This had reaction to the mill that caused the forced vibration mill to further accelerate the formation of chatter marks, where mill vibration came along with both the resonance and forced vibration.In the analysis of the mechanism on the chatter marks, the relationship between chatter marks spacing and vibration source was considered in successfully finding out the cause of the 1220 mill chatter marks generated, and then the chatter marks suppression measures were proposed with satisfied effects.

Key words： metrology cold rolling mill chatter mark vibration natural frequency

Received: 01 March 2014 Published: 20 October 2015

PACS:

TB936

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	XIE Chang-gui
	ZENG Hai

Cite this article:

XIE Chang-gui,ZENG Hai. Mechanism of the Strip Surface Chatter Marks of the 1220 Cold Rolling Mill[J]. Acta Metrologica Sinica, 2015, 36(6): 595-598.

URL:

http://jlxb.china-csm.org:81/Jwk_jlxb/EN/10.3969/j.issn.1000-1158.2015.06.09 OR http://jlxb.china-csm.org:81/Jwk_jlxb/EN/Y2015/V36/I6/595

［1］陈培林,王泽济,汪晨.带钢表面振动纹的研究［J］.世界钢铁,2002,2(4): 28-31.
［2］毛彬,周国荣,蒋复岱.基于小波变换的轧辊磨床振动信号分析研究［J］.噪声与振动控制,2007,(1):48-51.
［3］Hardwick B R. A technique for detection and measurement of chatter marks on roll surfaces［J］.Iron and Steel Technology,2003,80(4):65-69.

［4］Yun I S, Wilson W R D, Ehmann K F, et al. Review of Chatter Studies in Cold Rolling［J］. International Journal of Machine Tools& Manufacture, 1998, 38(12):1499-1530.
［5］罗忠辉,吴百海, 黄志坚.大型液压轧机轧制薄板异常振动及振纹研究［J］.机床与液压,2006, (1):105-107.
［6］Bollinger L A.Winding reel involvement in temper mill chatter ［J］.Iron and Steel Engineer, 1994,(11):27-29.
［7］Hardwick B,Benhafsi Y. Measurement of chatter marks formed during roll grinding［J］. Aluminium International Today,2006,16(3):10-14.
［8］陈平,樊华, 李俊洪,等. 1220HC冷连轧机振纹实测与抑制［J］.重庆大学学报,2011, 34(11):1-5.
［9］王永涛,臧勇,吴迪平,等.CSP轧机扭振中“伪拍振”的研究［J］.振动、测试与诊断,2009,29(2):209-212.
［10］米凯夫,张杰,李洪波,等.冷连轧机带钢表面振纹实测研究［J］.轧钢,2012,29(5):22-25.
［11］Zygmunt Drzymalaa, Andrzej Switoniowskia, Adam Bar. Non-linear vibrations in cold rolling mills［J］.Mecanique & Industries, 2003, 4 (2): 151-158.
［12］魏立群,瞿志豪,张杏耀,等.轧制润滑对1420冷连轧机机组自激振动的影响［J］. 钢铁研究学报,2006,18(2):28-31.
［13］王永利,汪友国,郭树宝.冷轧板振动痕缺陷原因分析［J］.宝钢技术,2007,(3):24-28.
［14］陈永辉,史铁林,林梅香.四辊冷带轧机再生颤振稳定性的统一理论［J］.中国机械工程, 2003, 14(6): 1408-1412.
［15］Kazama A, Oshige T. A defect inspection technique using polarized images for steel strip surface［J］.Proceedings of SPIE-The International Society for Optical Engineering,2008,7072: 70720L-1.
［16］赵志伟,杨景明,车海军,等.基于人工蜂群算法与反向传播神经网络的铝热连轧轧制力预测［J］.计量学报,2014,35(2):157-160.