电气设备剩余电压测试仪校准方法

doi:10.3969/j.issn.1000-1158.2024.05.03

Abstract
Figure/Table
References (16)
Related Citation (15)

Download: PDF (401 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The principle of the residual voltage tester for electric equipment is analyzed. A method for calibrating the residual voltage amplitude and delay time parameters of the tester based on the standard resistance-capacitance network method is proposed. The influences of the time constant of the standard resistor and the loss factor of the standard capacitor on the calibration results are analyzed based on the equivalent model of the impedance components. The calculation method of the reference value of residual voltage and delay time is derived for the calibration. The residual voltage tester is calibrated by using a circuit network composed of a 1MΩ AC standard resistor and a 1μF standard capacitor and the results show that the mentioned method meets the calibration for the tester. The uncertainty analysis of the measurement results is carried out. The expanded uncertainty for the residual voltage amplitude is 1.1% and 1.2% for the delay time. The main uncertainty component is the measurement uncertainty of the loss factor of the standard capacitor.

Key words： electrical metrology residual voltage delay time resistance-capacitance network loss factor measurement uncertainty

Received: 10 August 2023 Published: 23 May 2024

PACS:

TB971

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	FENG Jian
	HU Junjie
	XU Feng
	ZHOU Bihong

Cite this article:

FENG Jian,HU Junjie,XU Feng, et al. Calibration Method of Residual Voltage Tester for Electrical Equipment[J]. Acta Metrologica Sinica, 2024, 45(5): 626-630.

URL:

http://jlxb.china-csm.org:81/Jwk_jlxb/EN/10.3969/j.issn.1000-1158.2024.05.03 OR http://jlxb.china-csm.org:81/Jwk_jlxb/EN/Y2024/V45/I5/626

［1］	李雨明. 剩余电压测试［J］. 中国测试技术, 2008, 34(1): 40-42.
［7］	家用和类似用途电器的安全:GB 4706.1-2005［S］.北京: 中国标准出版社, 2005.
［13］	郭松林, 赵金宪. 基于矢量乘法器的最优滤波电力设备介质损耗角的实时测量方法［J］. 计量学报, 2009, 30(1): 84-87.
［2］	何敏, 涂荣, 吴少海. 医用电气设备中剩余电压测试的探讨［J］. 临床医学工程, 2012, 19(8): 1239-1240
	ZHANG X L, LAI L B, CAO L, et al, Study on standards of term on the residual voltage［J］. Standard Science, 2010(8): 37-41.
［3］	张学龙, 赖玲波, 曹俐, 等. 剩余电压测试的标准研究［J］. 标准科学, 2010(8): 37-41
［4］	蒋秋桃, 曹俐. 剩余电压条款及测试方法的探讨［J］. 中国医疗器械杂志, 2010, 34(3): 215-217.
	JIANG Q T, CAO L. Residual voltage of terms and test method［J］. Chinese journal of medical instrumentation. 2010, 34(3): 215-217.
	HE M, TU R, WU S H. A discussion about the test method of residual voltage in medical device［J］. China Medicine and Engineering, 2012, 19(8): 1239-1240.
［9］	曹俐. 剩余电压测试方法及其自动测量仪器的关键技术研究［D］. 长沙:中南大学, 2013.
［10］	冯建, 来磊, 石雷兵, 等. 交流电阻及其时间常数的准平衡式电桥精密测量技术［J］. 电工技术学报, 2017, 32(19): 187-192.
［11］	黄璐, 张钟华, 赵伟, 等. 精密宽频开尔文电桥的研制［J］. 计量学报, 2008, 29(2): 97-101.
	HUANG L, ZHANG Z H, ZHAO W, et al. Development of a wide-range AC Kelvin bridge［J］. Acta Metrologica Sinica, 2008, 29(2): 97-101.
［15］	陈炜峰, 蒋全兴. 电阻分压器性能与高压纳秒双指数脉冲的测量［J］. 东南大学学报: 自然科学版, 2006, 36(3): 374-379.
［16］	胡晓倩, 杨菁, 张莲, 等. 电阻分压器的集中参数电路模型及分析［J］. 重庆理工大学学报(自然科学), 2008, 22(7): 96-98.
	LI Y M. Residual voltage measurement［J］. China Measurement Technology, 2008, 34(1): 40-42.
［6］	医用电气设备第1部分: 基本安全和基本性能的通用要求:GB 9706.1-2020［S］.北京: 中国标准出版社, 2020.
［8］	王勇, 陈章进, 江超, 等. 基于FPGA的剩余电压检测系统的设计［J］. 电子技术应用, 2013, 39(3): 80-83.
	DAI D X, RUAN Y S, WANG Q. Calibration theory and measurement of the frequency characteristics of the four-pair terminal standard capacitor［J］. Acta Metrologica Sinica, 2005, 26(3): 263-266.
	GUO G L, ZHAO J X. The real-time measuring method on dielectric loss angle of electrical capacitive equipment［J］. Acta Metrologica Sinica, 2009, 30(1): 84-87.
	JIA D, L J H, CAI J H. Calculation of Test Cell Capacitance of Insulating Oils Dielectric Dissipation and Resistivity Tester［J］. Acta Metrologica Sinica, 2023, 44(2): 246-251.
	HU X Q, YANG J, ZHANG L. A lumped-parameter circuit model of resistive divider and its analysis［J］. Journal of Chongqing Institute of Technology (Natural Science), 2008, 22(7): 96-98.
［5］	测量、控制和实验室用电气设备的安全要求第1部分: 通用要求:GB 4793.1-2007［S］.北京: 中国标准出版社, 2007.
	WANG Y, CHEN Z J, JIANG C, et al, Design of detection system for residual voltage based on FPGA［J］. Measurement Control Technology and Instruments, 2013, 39(3): 80-83.
	FENG J, LAI L, SHI L B, et al. Precision measurement of AC resistance and time constant based on quasi-baance resistance bridge［J］. Transactions of China Electrotechnical Society,2017, 32(19): 187-192.
［12］	戴冬雪, 阮永顺, 王祁. 四端对标准电容器频率特性的校验理论及测定方法［J］. 计量学报, 2005, 26(3): 263-266.
［14］	贾多, 吕金华, 蔡晋辉. 绝缘油介质损耗与体积电阻率测试仪空杯电容值的计算［J］. 计量学报, 2023, 44(2): 246-251.
	CHEN W F, JIANG Q X. Performance of resistance divider and measurement of high-voltage nanosecond double exponential pulse［J］. Journal of Southeast University (Natural Science Edition), 2006, 36(3): 374-379.