|
|
|
| Dynamic and static calibration of nanosensors based on macro/micro motion control |
| ZHANG Hai-bo1,KUANG Ye2,TANG Yang-chao2 |
1.Heilongjiang Provincial Institute of Measurement & Verification, Harbin, Heilongjiang 150036, China
2.Institute of Ultra-precision Optoelectronic Instrument Engineering, Harbin Institute of Technology, Harbin, Heilongjiang 150001, China
|
|
|
|
|
Abstract To meet the requirements of calibration precision, calibration range and dynamic frequency response at the To meet the requirements of calibration precision, calibration range and dynamic frequency response at the same time, a macro/micro motion control method is used to drive the calibration device for fast, precise and wide-range positioning. the kinematics modeling of the micro-motion platform with static hinged/piezoelectric ceramic combination and the macro-motion platform with static pressure floatation/linear motor combination was carried out. And the transfer function of the platform is obtained. Two macro/micro control strategies, macro-follow-micro and micro-follow-macro, have been designed, simulated and compared. The experimental platform is built and the performance of the calibration device is tested. Experiment results show that the macro-follow-micro strategies has a higher dynamic response performance. Calibration device has the ability of 5 nm resolution in the whole stroke of 20 mm, and the dynamic frequency response up to 100 Hz in 0.05 mm amplitude in the sinusoidal frequency response, which can prove that the calibration device has dynamic and static calibration capability.
|
|
Received: 24 February 2017
Published: 06 July 2018
|
|
|
|
|
|
［1］刘凯,邹德福,廉五州,等.纳米传感器的研究现状与应用［J］.仪表技术与传感器,2008,(1):10-12.
［2］葛川,张德福,李朋志,等.电容式位移传感器的线性度标定与不确定度评定［J］.光学精密工程,2015,23(9):2546-2552.
［3］李昕. 线位移传感器自动校准装置研究［D］. 西安:西安电子科技大学, 2014.
［4］薛梓,叶孝佑,杨国梁,等.高精度位移传感器动静态溯源和校准装置的研制［J］.计量学报,2008,29(z1):57-60.
［5］张丰,曾燕华,张伟.线位移传感器的校准方法研究［J］.光学仪器,2016,38(1):63-68.
［6］Xue Z, Ye S L, Ye X Y. The study and realization of standard dynamic signals of dynamic characteristic calibration for high precision displacement sensor［C］// 5th International Symposium on Instrumentation Science And Technology. Shenyang, China, 2008, 7133: 713301-6.
［7］Heertjes M, Temizer B. Data-based control tuning in master-slave systems［C］//IEEE. The 2012 American Control Conference (ACC).Montreal,Canada, 2012: 2461-2466.
［8］陈琦.大行程纳米级定位工作台的结构设计［J］.光学精密工程, 2016, 24(5): 1065-1071.
［9］吴剑威,袁勇,崔继文,等.双工件台宏微交接系统设计及实验［J］.光学精密工程, 2015, 23(6): 1673-1680.
［10］Pahk H J, Lee D S, Park J H. Ultra precision positioning system for servo motor piezo actuator using the dual servo loop and digital filter implementation［J］. International Journal of Machine Tools & Manufacture, 2001, 41: 51-63.
［11］Buice E S, Otten D, Yang R H, et al. Design evaluation of a single-axis precision controlled positioning stage［J］. Precision engineering, 2009, 33(4): 418-424.
［12］Shinno H, Yoshioka H, Sawano H. A newly developed long range positioning table system with a sub-nanometer resolution［J］. CIRP Annals-Manufacturing Technology, 2011, 60(1):403-406.
［13］翟小玉. 三光轴集成式单频激光干涉测量关键技术研究［D］. 哈尔滨:哈尔滨工业大学, 2015. |
|
|
|
2018, Vol. 39 
